Difference between revisions of "GPIO Conflicts"

From HiveTool
Jump to: navigation, search
(Hive Interface Board)
(Hive Interface Board)
Line 1: Line 1:
 
==Hive Interface Board==
 
==Hive Interface Board==
HiveTool uses the default Pi GPIO assignment.  ie Pins number 3 and five are the I2C bus, Pin number 7 is the 1-Wire bus, pins 8 and 10 are used for the serial console, etc.
+
HiveTool uses the default Pi GPIO assignment.  ie Pins number 3 and 5 are the I2C bus, Pin number 7 is the 1-Wire bus, pins 8 and 10 are used for the serial console, etc.
  
 
A table of the GPIO pins used by Hivetool sensors is on the [[GPIO_Pinout#GPIO_ordered_by_Header_Pins|GPIO Pinout]] page.
 
A table of the GPIO pins used by Hivetool sensors is on the [[GPIO_Pinout#GPIO_ordered_by_Header_Pins|GPIO Pinout]] page.
  
If the sensors are not connected and the drivers are not enabled, there should be no conflict.
+
If the sensors are not connected and the drivers are not enabled, there should be no conflicts with other products that use the same GPIO pin.
  
 
==UPS PIco - Uninterruptible Power Supply==
 
==UPS PIco - Uninterruptible Power Supply==

Revision as of 05:09, 20 April 2019

Hive Interface Board

HiveTool uses the default Pi GPIO assignment. ie Pins number 3 and 5 are the I2C bus, Pin number 7 is the 1-Wire bus, pins 8 and 10 are used for the serial console, etc.

A table of the GPIO pins used by Hivetool sensors is on the GPIO Pinout page.

If the sensors are not connected and the drivers are not enabled, there should be no conflicts with other products that use the same GPIO pin.

UPS PIco - Uninterruptible Power Supply

UPS PIco - Uninterruptible Power Supply (HV3.0B+) conflicts with the DHT22s which are use GPIO27 (Pin13) & GPIO22 (Pin15).

The UPS PIco Uses the Following Pins

  • Serial Port (Firmware Updates): GPIO14 (Pin8) & GPIO15 (Pin10)
  • i2c Port: GPIO2 (Pin3) & GPIO3 (Pin5)
  • Pulse Train: GPIO27 (Pin13) & GPIO22 (Pin15)

It also uses the I2C addresses 68-6f:

$ i2cdetect -y 1
    0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- -- 
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
60: -- -- -- -- -- -- -- -- 68 69 6a 6b 6c 6d 6e 6f 
70: -- -- -- -- -- -- -- --

The UPS PIco is reported to work with Hivetool if you do not use the DHTxx sensors (which use GPIO pins 13 1nd 15) and do not use the DS3231 RTC (which uses I2C address 68).

Witty Pi Mini Realtime Clock and Power Management

Witty Pi Mini uses GPIO-4, GPIO-17, GPIO-2(SDA 1) and GPIO-3(SCL 1). The usage of GPIO-4 and GPIO-17 are customizable.

GPIO-4 and GPIO-17 are used by the 1-Wire bus and the LED.